06/23/2025 Release 0.2-202506231318   
- Support faster transfer with RF transceiver
- Improved error handling on heavy sensor loads
- Support for RF4, firmware 9.x
- Add option on Sensor Start
- Updated self diagnostics

03/16/2025 Release  0.2-03162155
- Added support RF Firmware update
- Add support for future change Frequency

01/15/2025 Release  0.2-01161433
- Fix issue with Logical Devices
- Add Recover option to MQTT data types

01/05/2025 Release 0.2-01061100
- Fix issue temperature sensor reading in 0-9.9 C range

01/02/2025 Release 0.2-01021429
- Fix issue with LED status and network issues

12/09/2024 Release 0.2-12091827
- Fix issue with switch On/Off and button On/Off processing

11/19/2024 Release 0.2-11191246
- Correct timeout and temperture warnings

11/17/2024 Release 0.2-11172012
- Handle Network report format error
- Show status on Health Warning No Rx Data

11/03/2024 Release 0.2-11141237
- Add option to change MQTT Device Id
- Update checkhealth reset RF on long timeout

11/03/2024 Release 0.2-11032254
- Add option to change MQTT Device Id

10/28/2024 Release 0.2-10281500
- Increase log file export for more history
- Add a new feature to allow special patching

10/25/2024 Release 0.2-10252138
- Fix issue with DHCP
- Show DHCP DNS Settings
- Update connection to support Cell Modem
- Enhance Sender connection status
- Add an option to Disable the Tech Support interface
- Allow option for AP to be enabled for 10 minutes on power update
- Setup OS firewall
- Reset RF Receiver if there are no new messages after 30 minutes

09/17/2024 Release 0.2.09181035
- Add option to Change RF Receiver Channel Number (require RF Firmware 7.70 or higher)
- Allow DNS to be blank and replaced with 0.0.0.0
- Detect no Enet connection
- Fix WLAN to display 0.0.0.0 when Enet disconnected
- Fix MQTT to show Not Connected when there is no Network
- Fix issue with enable/disable of Gateway AP

08/02/2024 Release 0.2-08020016
- Fix change to DHCP not resetting interface
- Fix update WLAN IP on IP change
- Fix manual time not updating hw clock
- Fix the change of ntp server to update hw clock
- Update HTTP Sender for changes in Server

07/28/2024 Release 0.2-07282326
- Fix issue with Export and new structure
- Fix AP to be same Id as Gateway
- Update AP to auto start on boot
- Change SFTP button to Export
- Improve RF data processing

07/19/2024 Release 0.2-07181958
- Update CPU temperature limits
- Improve LED and Relay Status Notifications
- Fix issue with Letters in device IDs
- Fix temperature reading if below zero

07/15/2024 Release 0.2-07160024
- Change timestamp on Sensor List to local time
- Update format of Health MQTT messages to use selected MQTT format
- Write system health events to logfile
- Update Network IP change for new nmcli support

07/07/2024 Release 0.2-07080054   
- Add last receive date-time to Sensor List
- Add Relay support for External Dry Contact
- Add RF Receiver Reset on startup
- Add Detect and display Sensor with Start Errors 

07/02/2024 Release 0.2-07031529
- Improve recovery time from an application failure
- Improve the time to process commands
- Add to the Log Export the System Health information
- Reduce the log messages when no server is defined
- Improve system startup
- Include manual patches from 06/28/2024

06/28/2024 Release
- Add option to set MQTT LifeByte Health Update Interval
- Add option to export System logs

06/28/2024 Release 0.1-06281452
- Update LifeByte set Status to "Issue" if RX count stops
- Update health check to send every 3 minutes from 5
- Fix health check startup race causing sender lockup
- Reduce time health monitor waits to restart system loader 

Open issues:
- Database needs improved house keeping tasks

Open Actions:
- Add LifeByte Update time
- Add Option to export system logs for offline analysis

06/24/2024 Release 0.1-06182135
- Improved time for command to process to max of 30 seconds
- Fix issue if NTP set, disable Set Manual Time
- Add Manual Update Process
- Add Display Latest Update document in Update Window
- Add MQTT Lifebyte health info every 3 minutes
- Add LED displays for Power, JemRF Server, MQTT status
- Add RF Receiver Count to System Health page
- Add test for RF receiver hanging